Slurry heat exchangers are in a category of their own. Unlike clean fluid exchangers, where corrosion and fouling are the main concerns, slurry exchangers have to deal with abrasion, settling, and erosion-on top of everything else.
We've specified, installed, and replaced slurry heat exchangers across mining, chemical processing, and wastewater treatment. Here's what we've learned about what works, what doesn't, and where the real energy savings come from.
What Makes a Slurry Heat Exchanger Different
A slurry is a mixture of solid particles in a liquid. The solids can be anything from fine mineral particles to organic fibers to catalyst beads. The liquid can be water, oil, or a chemical solution.
The challenges:
- Abrasion: solids wear down tube walls and pump impellers
- Settling: if velocity drops below a critical value, solids drop out of suspension
- Erosion-corrosion: worn surfaces corrode faster than intact surfaces
- Clogging: large particles or agglomerates block flow channels
What this means for exchanger design:
- Tubes need to be thicker or made of harder materials
- Velocities must be high enough to keep solids suspended (typically 1.5–3 m/s on the slurry side)
- Flow paths must be straight or gently curved-no sharp turns where solids can settle
- Inlet and outlet nozzles need to be larger to handle the abrasive flow
The Real Energy Savings: Where They Come From
Energy savings from slurry heat exchangers don't come from the exchanger itself-they come from the system. Here's what we've measured.
Source 1: Heat recovery
The most significant energy saving is recovering heat from slurry streams that would otherwise be wasted. We've seen plants recover 40–60% of the heat from hot slurry streams using properly designed exchangers.
Source 2: Reduced pumping power
A poorly designed slurry exchanger can have 2–3x the pressure drop of a clean fluid exchanger, because the tubes are smaller or the flow paths are more restrictive. A well-designed exchanger balances heat transfer and pressure drop.
Source 3: Less downtime
Slurry exchangers foul and wear faster than clean fluid exchangers. A unit that requires monthly cleaning consumes more energy in the long run than a unit that runs for 6 months between cleanings-because the fouled unit operates at lower efficiency and has more frequent startups and shutdowns.
The Three Types We've Actually Used
Shell-and-tube (straight tubes, slurry on tube side)
This is the most common design we specify. The slurry flows through the tubes at high velocity (1.5–3 m/s), keeping solids in suspension. The heating or cooling fluid flows on the shell side.
- Pros: Simple, reliable, easy to inspect and clean. Tubes can be replaced individually.
- Cons: Pressure drop can be high. Shell-side heating/cooling must be carefully designed to avoid thermal stress.
- We use this for: most mining and mineral processing applications, chemical slurries with moderate solids content.
Scraped surface
A rotating scraper continuously removes deposits from the heat transfer surface. The slurry flows through a narrow annular space between the tube and the scraper.
- Pros: Handles high-solids slurries that would plug shell-and-tube designs. Maintains heat transfer even with sticky or fouling materials.
- Cons: High maintenance cost (scraper blades wear out). Complex mechanical seal. Limited to lower pressures (typically below 20 bar).
- We use this for: food processing (slurries with organic solids), polymer slurries, and any service that plugs shell-and-tube designs.
- We don't use it for: high-pressure services or applications with hard abrasive particles (the scrapers wear out too fast).
Plate-and-frame (with special slurry plates)
Some manufacturers offer plate-and-frame designs with wide gaps (5–10 mm) to handle slurries. The plates have special patterns to promote turbulence and keep solids moving.
Pros: Very compact. High heat transfer coefficients.
Cons: Limited to low pressures. Plates are expensive to replace when they wear out. Cleaning requires disassembly.
We use this for: low-pressure services with fine solids (below 100 microns). We don't use it for coarse or highly abrasive slurries.
Our cleaning experience:
| Deposits Type | Cleaning Method | Cleaning Interval | Notes |
| Hard scale | Acid cleaning (CIP) | 3–6 months | Monitor acid concentration-too high corrodes tubes |
| Organic deposits | Hot water or caustic CIP | 1–3 months | Temperature matters-too hot bakes deposits on |
| Settled solids | Mechanical (water lance or rodding) | 2–4 months | Requires shutdown. Shell-and-tube only-scraped surface handles this better |
Selection Checklist for Slurry Heat Exchangers
Before specifying a slurry exchanger:
- Solids characterization – particle size, hardness, settling velocity, abrasiveness. Get a sample and test it.
- Velocity requirement – calculate settling velocity. Add 20–30% margin. Check that the required velocity doesn't exceed erosion limits.
- Erosion allowance – specify extra wall thickness based on solids hardness and velocity. Don't use standard tube thickness.
- Cleaning access – CIP connections? Drain/flush ports? Can the bundle be removed for mechanical cleaning?
- Material – match to both corrosion and abrasion. 316L is often acceptable. Duplex may be better.
- Design type – shell-and-tube for most slurries. Scraped surface for high-viscosity or sticky slurries.
- Pressure drop – check pump capability. Slurry exchangers have higher pressure drop than clean fluid exchangers.
- Vendor experience – not every manufacturer builds slurry exchangers. Ask for references in similar solids applications.
